View Profile: Cyorg - CafeRacer Forums
Close

Tab Content
  • Cyorg's Avatar
    06-08-2019, 01:11 PM
    Bist du ein Kraut?
    29 replies | 597 view(s)
  • Cyorg's Avatar
    06-05-2019, 03:38 PM
    Cyorg replied to a thread KZ750 project in Project Builds
    Great minds (or maybe cheap old bastards) think alike.
    72 replies | 1916 view(s)
  • Cyorg's Avatar
    06-04-2019, 10:39 AM
    Cyorg replied to a thread My Ape project in Project Builds
    Oh well.... for the time run, the ball bearings won’t give any indication what’s gone on down below, although the cam/followers may. PITA, but...
    29 replies | 565 view(s)
  • Cyorg's Avatar
    06-03-2019, 01:09 PM
    Cyorg replied to a thread My Ape project in Project Builds
    Ps...If you want a tach that is just a tach, have a look at Scitsu. They won’t break the bank. Can’t personally vouch for them, although the guy in...
    29 replies | 565 view(s)
  • Cyorg's Avatar
    06-03-2019, 12:56 PM
    Cyorg replied to a thread My Ape project in Project Builds
    That has been my experience with the engines I have worked on. Usually the cam suffers first, so if things look ok there, then you’re probably ok...
    29 replies | 565 view(s)
  • Cyorg's Avatar
    06-03-2019, 10:33 AM
    Cyorg replied to a thread My Ape project in Project Builds
    Have you done any poking around to check things out? Being a plain bearing crank, they obviously don’t like that sort of thing. How easy is it to...
    29 replies | 565 view(s)
  • Cyorg's Avatar
    06-03-2019, 10:21 AM
    Cyorg replied to a thread My Ape project in Project Builds
    So your announcing that here just to punish yourself? Everyone here has done stupid shit, not everyone will admit it. I drained the oil out of the...
    29 replies | 565 view(s)
  • Cyorg's Avatar
    06-03-2019, 10:03 AM
    Cyorg replied to a thread Engine rattle in Technical
    That sounds normal to me. Dogs are just randomly sitting so they won’t engage. Rotate them slightly and they’ll slide in. The Guzzi does that...
    19 replies | 343 view(s)
  • Cyorg's Avatar
    06-03-2019, 09:53 AM
    Cyorg replied to a thread My Ape project in Project Builds
    What hole did you use? Straight into the crankcase?
    29 replies | 565 view(s)
  • Cyorg's Avatar
    06-03-2019, 09:47 AM
    Cyorg replied to a thread Good read, IOM, Dunlop's in General
    Did you ever watch the movie ďRoadĒ narrated by Liam Nelson? It used to be on Netflix, but gone now. You can still find it out there if you havenít...
    3 replies | 83 view(s)
  • Cyorg's Avatar
    06-01-2019, 10:42 AM
    Cyorg replied to a thread KZ1000 monoshock conversion in General
    I used a BMW swingarm that came with needle rollers (for the swingarm pivots) no idea how many miles were on it, but based on their condition (with...
    14 replies | 320 view(s)
  • Cyorg's Avatar
    05-30-2019, 05:57 PM
    Well someone went to town. I suppose with enough time and money.... but IMHO life is too short to bother with them. In that link..... what do you...
    4 replies | 87 view(s)
  • Cyorg's Avatar
    05-30-2019, 01:50 PM
    Cyorg replied to a thread KZ1000 monoshock conversion in General
    Older Ducati Monster uses a couple of those joints on the rear shock fork. I made a knockoff of that fork and added heim joints to both ends. Makes...
    14 replies | 320 view(s)
  • Cyorg's Avatar
    05-30-2019, 01:34 PM
    I have to deal with a situation like that on different engine. Just going to machine a top hat out of 6061 and fit it to the cases. Iím guessing you...
    4 replies | 87 view(s)
  • Cyorg's Avatar
    05-30-2019, 11:15 AM
    Cyorg replied to a thread KZ1000 monoshock conversion in General
    That swingarm has been extended a bunch. Not sure why youíd want to extend it that much unless youíre climbing hills. This is an interesting shock...
    14 replies | 320 view(s)
  • Cyorg's Avatar
    05-29-2019, 05:58 PM
    Itís a bit of an illusion. I had to shovel it off and wipe it down to make way for the sorting. I do ďtryĒ and keep things civilized and usually set...
    1945 replies | 103279 view(s)
  • Cyorg's Avatar
    05-29-2019, 02:03 PM
    Counting teeth.
    1945 replies | 103279 view(s)
  • Cyorg's Avatar
    05-28-2019, 11:29 AM
    You know what will happen if you donít replace the seals...... If you are ever stuck for a gasket, that water based kids paint (the thicker kind)...
    1945 replies | 103279 view(s)
  • Cyorg's Avatar
    05-24-2019, 02:00 PM
    My memory is a little fuzzy..... maybe Iíve even mentioned this before, but if the balancer chain adjuster has run out of adjustment, you can pull...
    192 replies | 9893 view(s)
  • Cyorg's Avatar
    05-24-2019, 10:12 AM
    Wish I got that one more often.... might get more shit done around here.
    8 replies | 144 view(s)
  • Cyorg's Avatar
    05-24-2019, 09:09 AM
    Yes... the site goes into vapour lock every once in a while. The what you doing today thread is still stuck in a time warp.
    8 replies | 144 view(s)
  • Cyorg's Avatar
    05-23-2019, 09:42 AM
    Why some early snowmobile engines had nice clean combination chambers. No air filters or air boxes, so sucked in just enough snow to keep things...
    192 replies | 9893 view(s)
  • Cyorg's Avatar
    05-22-2019, 11:04 AM
    Cyorg replied to a thread Engine rattle in Technical
    No idea because Iím not into those wretched things. If it was a Ducati or MG, you wouldnít be able to hear yourself think over the clutch rattle....
    19 replies | 343 view(s)
  • Cyorg's Avatar
    05-19-2019, 05:46 PM
    That makes sense to me in that your fuel doesn’t sit in there long enough to collect much water, so you don’t get the swelling. Congrats on the...
    1945 replies | 103279 view(s)
  • Cyorg's Avatar
    05-19-2019, 09:15 AM
    My bride never says boo about M/C purchases, but Iím always suspicious that there is another shoe that will drop... usually in the form of some shiny...
    1945 replies | 103279 view(s)
No More Results
About Cyorg

Basic Information

Signature


"Non urinat in ventum"

Statistics


Total Posts
Total Posts
1,962
Posts Per Day
1.06
General Information
Last Activity
06-16-2019 11:04 AM
Join Date
05-17-2014
Referrals
0