View Profile: irk_miller - CafeRacer Forums
Close

No More Results
About irk_miller

Basic Information

About irk_miller
Location:
Augusta, GA
Occupation:
teacher

Statistics


Total Posts
Total Posts
175
Posts Per Day
0.87
General Information
Last Activity
05-11-2019 10:00 AM
Join Date
11-02-2018
Referrals
0

46 Likes

Page 1 of 4 123 ... LastLast
  1. 540nova
    540nova liked post by irk_miller On thread : [email protected] Old Guys!!
    In my many years working as a technician and machinist, if I had a dime for every non-working, effed up design I've seen by an educated engineer, I would be a rich man. My entire job working for...
    Liked On: 05-09-2019, 05:52 PM
  2. jcw
    jcw liked post by irk_miller On thread : Building Custom Seat Question
    Except for the choppers I build, I make the base out of epoxy fiberglass and I carve the seat pad shape out of insulation from. Then I make a plaster mold of the insulation foam form and cast it in...
    Liked On: 04-18-2019, 08:37 AM
  3. woodsman
    woodsman liked post by irk_miller On thread : Building Custom Seat Question
    Except for the choppers I build, I make the base out of epoxy fiberglass and I carve the seat pad shape out of insulation from. Then I make a plaster mold of the insulation foam form and cast it in...
    Liked On: 04-18-2019, 05:18 AM
  4. Hoofhearted
    Hoofhearted liked post by irk_miller On thread : Classic Hare & Hound
    So many of these guys were just tough. https://www.youtube.com/watch?v=3a64niu0db8
    Liked On: 04-08-2019, 09:30 PM
  5. sonsothunder
    sonsothunder liked post by irk_miller On thread : Classic Hare & Hound
    That's Bruce Brown. Same dude that did On Any Sunday and Endless Summer.
    Liked On: 04-08-2019, 03:50 PM
  6. sonsothunder
    sonsothunder liked post by irk_miller On thread : Classic Hare & Hound
    So many of these guys were just tough. https://www.youtube.com/watch?v=3a64niu0db8
    Liked On: 04-08-2019, 03:50 PM
  7. Tanshanomi
    Tanshanomi liked post by irk_miller On thread : Classic Hare & Hound
    That's Bruce Brown. Same dude that did On Any Sunday and Endless Summer.
    Liked On: 04-08-2019, 11:36 AM
  8. Tanshanomi
    Tanshanomi liked post by irk_miller On thread : Classic Hare & Hound
    So many of these guys were just tough. https://www.youtube.com/watch?v=3a64niu0db8
    Liked On: 04-08-2019, 10:26 AM
  9. Andyshep
    Andyshep liked post by irk_miller On thread : Cleaning out fuel tank.
    I used S100, Purple Power, or sometimes Pine Sol, to clean out any grease/fuel. Sometimes I use vinegar. Then I de-rust with Phosphoric Prep and Etch from the hardware store (sold at Home Depot in...
    Liked On: 03-14-2019, 09:33 AM
  10. TrialsRider
    TrialsRider liked post by irk_miller On thread : MIG Welding an Exhaust Header - CB400T
    I did an experiment with my chopper on pipe length, with some very obvious differences. Originally, I ran the pipe at over 36" from the collector. Then, I cut 8" off which was a bump in throttle...
    Liked On: 03-04-2019, 01:47 PM
  11. jakejensen
    jakejensen liked post by irk_miller On thread : MIG Welding an Exhaust Header - CB400T
    I did an experiment with my chopper on pipe length, with some very obvious differences. Originally, I ran the pipe at over 36" from the collector. Then, I cut 8" off which was a bump in throttle...
    Liked On: 03-04-2019, 01:43 PM
  12. monkey
    monkey liked post by irk_miller On thread : The "Whatcha Doin Today" Thread
    Machined trim rings to retrofit Pontiac Catalina tail lights onto my Volksrod. 96897
    Liked On: 03-04-2019, 05:43 AM
  13. jakejensen
    jakejensen liked post by irk_miller On thread : The "Whatcha Doin Today" Thread
    Machined trim rings to retrofit Pontiac Catalina tail lights onto my Volksrod. 96897
    Liked On: 03-03-2019, 07:32 AM
  14. TrialsRider
    TrialsRider liked post by irk_miller On thread : introduce myself
    If you have the money, those Ceriani sure are a work of art. 96821
    Liked On: 02-19-2019, 05:48 AM
  15. jcw
    jcw liked post by irk_miller On thread : The "Whatcha Doin Today" Thread
    I started re-designing the front clip on a rod I traded for this weekend. There are lots of questionable decisions on this thing, but plenty of meat left to be a crazy fun ride. 96701
    Liked On: 02-14-2019, 02:36 PM
Page 1 of 4 123 ... LastLast