XS650 in a 350 Engine Bolts
Close

XS650 in a 350 Engine Bolts

This is a discussion on XS650 in a 350 Engine Bolts within the Project Builds forums, part of the Caferacer.net Forums category; What tap do i need to do this and do i have to pre drill the holes into the block before i tap them cause ...

Page 1 of 5 123 ... LastLast
Results 1 to 10 of 45
  1. #1
    Senior Member RondaDAHonda's Avatar
    Join Date
    Nov 2009
    Location
    Marietta, GA, USA.
    Posts
    189

    XS650 in a 350 Engine Bolts

    What tap do i need to do this and do i have to pre drill the holes into the block before i tap them cause the bolts are huge! Any info will be helpful..

    Thanks Red

  2. #2
    Senior Member RondaDAHonda's Avatar
    Join Date
    Nov 2009
    Location
    Marietta, GA, USA.
    Posts
    189
    i know the tap is M10-1.25

  3. #3
    Senior Member RondaDAHonda's Avatar
    Join Date
    Nov 2009
    Location
    Marietta, GA, USA.
    Posts
    189
    i know the tap is M10-1.25

  4. Remove Advertisements
    CafeRacer.net
    Advertisements
     

  5. #4
    Senior Member hahnda's Avatar
    Join Date
    Dec 2006
    Location
    Cameron, WI, USA.
    Posts
    659
    You are putting an XS650 engine in a CB350 frame? Does it fit?
    http://www.scramblercycle.com

  6. #5
    Senior Member hahnda's Avatar
    Join Date
    Dec 2006
    Location
    Cameron, WI, USA.
    Posts
    659
    You are putting an XS650 engine in a CB350 frame? Does it fit?
    http://www.scramblercycle.com

  7. #6
    Senior Member burntblacktoast's Avatar
    Join Date
    Mar 2008
    Location
    bellflower, il, USA.
    Posts
    204
    XS cylinder studs, perhaps? Must be a pretty boss engine.

  8. #7
    Senior Member burntblacktoast's Avatar
    Join Date
    Mar 2008
    Location
    bellflower, il, USA.
    Posts
    204
    XS cylinder studs, perhaps? Must be a pretty boss engine.

  9. #8
    Senior Member spacmanspif300's Avatar
    Join Date
    Sep 2008
    Location
    , , Mongolia.
    Posts
    1,763
    Drilling always comes before tapping, for sure. I'm still not totally clear what is being discussed here, though.

  10. #9
    Senior Member spacmanspif300's Avatar
    Join Date
    Sep 2008
    Location
    , , Mongolia.
    Posts
    1,763
    Drilling always comes before tapping, for sure. I'm still not totally clear what is being discussed here, though.

  11. #10
    Senior Member RondaDAHonda's Avatar
    Join Date
    Nov 2009
    Location
    Marietta, GA, USA.
    Posts
    189
    putting xs650 studs into my 350 engine what do i need to do?

    Red

Page 1 of 5 123 ... LastLast

Sponsored Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Stripped Engine Casing Bolts
    By pacreamer in forum Technical
    Replies: 8
    Last Post: 05-29-2011, 06:48 PM
  2. Nuts and Bolts
    By ghetto_racer in forum Technical
    Replies: 4
    Last Post: 10-01-2008, 09:07 AM
  3. STUBORN BOLTS
    By ahracer1 in forum General
    Replies: 16
    Last Post: 04-03-2008, 09:44 AM
  4. Yam xs650 engine upgrades
    By nf343vr in forum Technical
    Replies: 2
    Last Post: 11-06-2007, 11:17 PM
  5. where do you buy TI bolts
    By jaguar in forum Technical
    Replies: 13
    Last Post: 09-20-2007, 02:23 PM