My little CB100 - Page 3
Close

My little CB100

This is a discussion on My little CB100 within the Project Builds forums, part of the Caferacer.net Forums category; That was my thought train to. Drilled and tapped a hole, just didn't hold. Couldn't get a good angle on the shaft, so I found ...

Page 3 of 7 FirstFirst 12345 ... LastLast
Results 21 to 30 of 70
Like Tree7Likes

Thread: My little CB100

  1. #21
    Member mitchi's Avatar
    Join Date
    Sep 2013
    Location
    Georgia
    Posts
    33
    That was my thought train to. Drilled and tapped a hole, just didn't hold.

    Couldn't get a good angle on the shaft, so I found a replacement..........pulled the engine, and went to town...........first time ever going into and splitting an engine.

    Wish me luck......
    "If it ain't raining, I'm riding"~~~~~~{iii}?~~~~~~~prost~~~~~

  2. #22
    Senior Member TrialsRider's Avatar
    Join Date
    Jan 2011
    Location
    Ontario, Canada
    Posts
    5,387
    Oh my.

    Should have made it a keyway and gone with a better lever, much easier and cheaper.
    ... take pictures of everything you take apart.

  3. #23
    Senior Member CaTacL1sm's Avatar
    Join Date
    Feb 2009
    Location
    Fort Knox, Kentucky
    Posts
    2,293
    or just weld the kick lever on...
    Quote Originally Posted by alwhite00 View Post
    Fuck all of you guys. Get into your little circle jerk and have fun. Thought this may be a pretty cool message board but damn, you guys are assholes.

  4. Remove Advertisements
    CafeRacer.net
    Advertisements
     

  5. #24
    Member mitchi's Avatar
    Join Date
    Sep 2013
    Location
    Georgia
    Posts
    33
    Quote Originally Posted by CaTacL1sm View Post
    or just weld the kick lever on...
    Trust me......seriously considered, till I thought about cleaning the rotor filter out during oil changes.
    "If it ain't raining, I'm riding"~~~~~~{iii}?~~~~~~~prost~~~~~

  6. #25
    Member mitchi's Avatar
    Join Date
    Sep 2013
    Location
    Georgia
    Posts
    33
    Well, got the engine rebuilt with new kicker. Reinstalled, and running.

    Been wiring the lights and stuff. Got a cb160 headlight bucket, now need a speedometer to fit in there. (one that works for a decent price)

    Not really worried if the ratio is not the same.
    Attached Images Attached Images   
    "If it ain't raining, I'm riding"~~~~~~{iii}?~~~~~~~prost~~~~~

  7. #26
    jcw
    jcw is offline
    Senior Member jcw's Avatar
    Join Date
    Jul 2015
    Location
    chicago burbs
    Posts
    2,068
    Late to the party, but I would have put a couple spot welds on the outside that you could grind off if you wanted to remove the kick lever.

    But you did the right thing...

  8. #27
    Member mitchi's Avatar
    Join Date
    Sep 2013
    Location
    Georgia
    Posts
    33
    Thanks, it was a good learning experience.

    I tore open a CL350 engine at the same time just because I seen a lot of permatex around the edges, and man, what a lot:
    Attached Images Attached Images    
    "If it ain't raining, I'm riding"~~~~~~{iii}?~~~~~~~prost~~~~~

  9. #28
    Senior Member TrialsRider's Avatar
    Join Date
    Jan 2011
    Location
    Ontario, Canada
    Posts
    5,387
    His day job is at waffle house.

  10. #29
    Senior Member CaTacL1sm's Avatar
    Join Date
    Feb 2009
    Location
    Fort Knox, Kentucky
    Posts
    2,293
    but did it leak?
    Quote Originally Posted by alwhite00 View Post
    Fuck all of you guys. Get into your little circle jerk and have fun. Thought this may be a pretty cool message board but damn, you guys are assholes.

  11. #30
    Member mitchi's Avatar
    Join Date
    Sep 2013
    Location
    Georgia
    Posts
    33
    Quote Originally Posted by CaTacL1sm View Post
    but did it leak?

    Ha ha.........never had it filled to know.

    Bet it didn't, but might have been the reason for the fried top end.
    "If it ain't raining, I'm riding"~~~~~~{iii}?~~~~~~~prost~~~~~

Page 3 of 7 FirstFirst 12345 ... LastLast

Sponsored Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •