Search Results - CafeRacer Forums
Close

Search:

Type: Posts; User: Johnny Gaijin

Page 1 of 5 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    3
    Views
    922

    yeah, should have said so but that barrel...

    yeah, should have said so but that barrel adjuster is tightened to the limit as well...
  2. Replies
    3
    Views
    922

    cb360 throttle cable

    my bike is idling high... adjusting the idle adjust screw doesn't do anything. pushing the throttle forward will lower the idle, but i've got that push cable as tight as i can get it... any...
  3. Replies
    36
    Views
    4,787

    i don't remember the numbers but i did check to...

    i don't remember the numbers but i did check to make sure they matched.
  4. Replies
    36
    Views
    4,787

    even when warm it only idles (or often just dies)...

    even when warm it only idles (or often just dies) on one cylinder.
  5. Replies
    36
    Views
    4,787

    yeah i'm not really worried about the choke plate...

    yeah i'm not really worried about the choke plate anymore.
    it idles on one cylinder but runs on both when i get the rpm's up a bit.
  6. Replies
    36
    Views
    4,787

    i hosed 'em down with carb cleaner and wiped up...

    i hosed 'em down with carb cleaner and wiped up with a cloth. i made sure to blow carb cleaner down the idle passages... is that surface grime gonna be an issue?
  7. Replies
    36
    Views
    4,787

    three taps of a hammer later and problem solved. ...

    three taps of a hammer later and problem solved.
    although the real problem, idling on one cylinder, still exists. timing and tappet adjust up next.
  8. yeah the '75 CL360 had a drum brake, the '75...

    yeah the '75 CL360 had a drum brake, the '75 CB360 had a disk.
  9. Replies
    36
    Views
    4,787

    fits w/o the o-ring, oil allows the seat to be...

    fits w/o the o-ring, oil allows the seat to be pushed in but the o-ring just pushes it back up. grrr.
  10. Replies
    36
    Views
    4,787

    ok so yeah i cleaned out idle passages, i just...

    ok so yeah i cleaned out idle passages, i just didn't know that's what they were called (although i figured that's what you meant). yeah i'm enjoying learning how to work on my bike and intend to...
  11. Replies
    36
    Views
    4,787

    i'm putting in rebuild kits because some of the...

    i'm putting in rebuild kits because some of the gaskets are brittle and i figured since i've already taken the carbs off and rebuild kits aren't too expensive i might as well.
    i've got a friend of a...
  12. Replies
    36
    Views
    4,787

    yeah i know there's more than one jet. i got the...

    yeah i know there's more than one jet. i got the rebuild kits so i'm not gonna bother cleaning the old ones. yes to the stock filters.
  13. Replies
    36
    Views
    4,787

    yeah, i pulled the jets and looked at 'em. ...

    yeah, i pulled the jets and looked at 'em. looked fine, but what do i know (not much).
  14. Replies
    36
    Views
    4,787

    so people say trouble idling could be caused by a...

    so people say trouble idling could be caused by a clogged jet. if that was the case would the jet be visibly clogged or are we talking some microscopic stuff here? cause mine looked fine... some...
  15. Replies
    36
    Views
    4,787

    so correct me if i'm wrong because i really don't...

    so correct me if i'm wrong because i really don't know much but...

    the flap that's missing is what flips when you use the choke, in the normal position it's wide open so the the flap is...
  16. Replies
    36
    Views
    4,787

    the bike does fine once you're going ten miles an...

    the bike does fine once you're going ten miles an hour, it's just below that that there's a problem, so i'm hoping the engine is ok. <profuse knocking on wood>
    different question:
    the big gasket...
  17. Replies
    36
    Views
    4,787

    cb360 carbs

    the bike i bought two weeks ago wasn't idling well so i pulled off the carbs planning on cleaning them, maybe putting in new gaskets or whatever. i didn't expect this:...
  18. Replies
    44
    Views
    1,769

    i just bought a running cb360 for $400 bucks in...

    i just bought a running cb360 for $400 bucks in seattle. well actually i had to drive an hour and a half out of seattle to get it but whatever. no point to this post really, i'm just really proud of...
  19. Replies
    44
    Views
    1,769

    i just bought a running cb360 for $400 bucks in...

    i just bought a running cb360 for $400 bucks in seattle. well actually i had to drive an hour and a half out of seattle to get it but whatever. no point to this post really, i'm just really proud of...
  20. Replies
    15
    Views
    3,464

    ouch, too late. good to know in the future...

    ouch, too late. good to know in the future though. thanks.
  21. Replies
    15
    Views
    3,464

    ouch, too late. good to know in the future...

    ouch, too late. good to know in the future though. thanks.
  22. Replies
    15
    Views
    3,464

    talked to a honda dealer who ordered me an oem...

    talked to a honda dealer who ordered me an oem cable. FOR 45 DOLLARS. sheesh. it'd better be gold plated or magic or something.
  23. Replies
    15
    Views
    3,464

    cables are double ended, you can't just cut them...

    cables are double ended, you can't just cut them to size and unless i had some serious reassurance that it was gonna work i don't think i'd feel comfortable soldering the ends together myself. ebay...
  24. Replies
    15
    Views
    3,464

    you can't say "make your own" period. you have...

    you can't say "make your own" period. you have to say "make your own; here's a fun and easy to understand website: www.makeyourowncb360throttlecables.com" see the difference? one has a semicolon!...
  25. Replies
    15
    Views
    3,464

    cb360 throttle cables

    know where a guy can get one? motion pro doesn't make them (although they will custom fab one for 35 dollars and it will take 3 weeks) and i don't know where else to look...
Results 1 to 25 of 116
Page 1 of 5 1 2 3 4