Search Results - CafeRacer Forums
Close

Search:

Type: Posts; User: photoputz83

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. you can get a vermont title in any state and...

    you can get a vermont title in any state and transfer it over to the state at which you live. its a viable loophole, but i have never done that as i have never run into this issue before. both the...
  2. how hard is it to vermont title a bike. i have...

    how hard is it to vermont title a bike. i have heard of this, but dont know how fast nor easy it is.
  3. title question for a title that uses engine vin

    so i picked up a kawasaki s3 lastyr ea for pretty cheap. i knew it was a bad engine when i picked it up, and was going to replace it. the title on the bike uses the engine vin, and not the frame. i...
  4. It is slightly oversized. It went from a stock 90...

    It is slightly oversized. It went from a stock 90 to a 100. I have the same tire on my 360t and it has 3/8 on each side . It's tight but haven't hadvantage issues thus far. Any bugger than a 100...
  5. 1874118742

    1874118742
  6. Front wheel issue (offset to one side) cb350f

    so i laced up my third set of wheels and trued them to within .0314 (around 1/32) verified by dial indicator on truing stand. i thought all was good to go at that point so i had the tire mounted and...
  7. Also if you read the comments previously, I never...

    Also if you read the comments previously, I never said I was going to fabricate a new swingarm. I was asking if it were possible to swap a swingarm on to the stock frame without much modification. It...
  8. Messed around in solidworks for a few weeks...

    Messed around in solidworks for a few weeks before I even said id think about doing it. got things as close as possible with the longer wheelbase taken into account. I tried to get him to change his...
  9. Maybe I was wrong to assume that asking would be...

    Maybe I was wrong to assume that asking would be helpful. I have never had the need to extend a swingarm before, so I don't have the experience in doing so. when someone asks for a modification like...
  10. sorry about the typos in the original post. fat...

    sorry about the typos in the original post. fat finger syndrome today. anyway, the reason being the customer wants a little more length on the bike. The fork is being swapped already. He originally...
  11. 74 cb350 four swingarm options. Looking for longer.

    I'm buildingba 74 cb350 four and wanted to push the rear back a bit, around a couple inches. I was somewhat curious as to if any longer singarms will bolt up, or if there are any that with minimal...
  12. Brand new carbs, both flowing fuel through idle...

    Brand new carbs, both flowing fuel through idle circuit and at full throttle. Thinking it's an electrical issue. Coils, points, or plug caps. Valve clearance is at .0035. A hair over spec. But just...
  13. New lines and petcock was rebuilt when bike was...

    New lines and petcock was rebuilt when bike was redone. I will however try the swapping of the coils. Thanks a bunch.
  14. So the valves are set vm32 carbs have been set up...

    So the valves are set vm32 carbs have been set up and bench sync has been done. Both spark plugs have spark. Cold compression is 15 pounds off of what the specifications say it should be warm. Still...
  15. The original carbs did the same thing. Went...

    The original carbs did the same thing. Went through an ultrasonic bath, cleaned all orifices, and synchronized.
  16. Doing it now. Just picked up a set of feeler...

    Doing it now. Just picked up a set of feeler guages from my matco rep. I'll post what I find.
  17. 1975 cb500t intermittent ignition/firing on left cyl.

    I'm working on a cb500t and am having a few issues with the left cyl only firing when the throttle is applied, or the bike is above 2500 rpm. Picked the bike up with 12k on the clock. Was an okay...
  18. Replies
    4
    Views
    1,828

    cb360 swingarm swap or extension kit?

    So earlier this year I decided to build a vintage bike for speed week 2015. I am finishing work on the frame, and all the carbon composite bits and pieces. I am down to the swingarm and am having a...
  19. well i ended up pulling the ignition switch off...

    well i ended up pulling the ignition switch off and replacing it. it seems as if the switch that came off the bike finally failed. thanks for pointing me in the right direction!
  20. the main fuse when the ignition is on is showing...

    the main fuse when the ignition is on is showing no continuity and no power to the battery positive. ill try to trace back to the battery to see where the connection is lost.
  21. so i ended up taking off the fuse box and...

    so i ended up taking off the fuse box and checking the connections/solder joints. all were good. removed the headlight bucket and looked for any loose wires and found none. the headlight fuse is...
  22. -17 degrees windchill isnt easy to work in...

    -17 degrees windchill isnt easy to work in especially when you only have partial function of your left hand as it is. besides the screen on my fluke meter kept on fogging up and at that temperature...
  23. i though that as well! but i pulled the fuse box...

    i though that as well! but i pulled the fuse box off and looked yesterday and all the connection points are in place. did a full continuity test on the fuse box, and every part of the electrical...
  24. tail light fell off? the tail light is an axle...

    tail light fell off? the tail light is an axle mount and is still in place.
  25. there is a fender on the bike, and the ground...

    there is a fender on the bike, and the ground isnt through the fender! i dont know why it would be through the fender as from the factory it never was.
Results 1 to 25 of 51
Page 1 of 3 1 2 3