Search Results - CafeRacer Forums
Close

Search:

Type: Posts; User: 747

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    56
    Views
    21,633

    I would mill those toolholders till I got the...

    I would mill those toolholders till I got the toolbit on the center line of your machine
  2. Replies
    56
    Views
    21,633

    got an early start and turned the .5" dies and...

    got an early start and turned the .5" dies and got the holes dimpled 6125
  3. Replies
    56
    Views
    21,633

    mill the bottom off the tool shank if it is a...

    mill the bottom off the tool shank if it is a insert type tool holder . Post a pic of your cutting tools
  4. Replies
    56
    Views
    21,633

    nice score!

    nice score!
  5. Replies
    56
    Views
    21,633

    what model is your machine , there are tons...

    what model is your machine , there are tons videos on turning on ytube
  6. Replies
    56
    Views
    21,633

    sure you can, I don't have a press so I tapped...

    sure you can, I don't have a press so I tapped the bottom die and draw the top in with a .625 bolt . With thin material it takes very little force to dimple these holes. I still need to make a .5...
  7. Replies
    56
    Views
    21,633

    before and after

    Here's before and after60606061
  8. Replies
    56
    Views
    21,633

    Finished Die

    6059I finished turning and milled flats on female die. Wire wheeled the chain guard, the dimpled the 1.250 holes6057[/ATTACH]6058
  9. Replies
    56
    Views
    21,633

    male die in the mini lathe5916Finished turning...

    male die in the mini lathe5916Finished turning die set for 1.25 dia hole, just need to mill flats on the female die.5917
  10. Replies
    56
    Views
    21,633

    got some vacation time , the temp is about -5...

    got some vacation time , the temp is about -5 here so it short trips out o the barn and get something done on the project . Turning the male side of dimple die, finished the female side a few days...
  11. Replies
    56
    Views
    21,633

    58165817 drilled guard and started the dimple...

    58165817 drilled guard and started the dimple die female is turned justs needs to tapped
  12. Replies
    56
    Views
    21,633

    Chain guard modification

    ]As I was going through the parts stash, I came across a chain guard from 72/73 250/350 triple. Its drilled with a series of holes, but its shorter and the mounting brackets are in different...
  13. Replies
    6
    Views
    652

    Info on Dimple dies

    Has anyone turned there own dimple dies for deforming sheetmetal?
  14. Replies
    14
    Views
    7,283

    Sticky: just tried to post some pics , and I've posted...

    just tried to post some pics , and I've posted before no luck this time any suggestions ?
  15. Replies
    56
    Views
    21,633

    55155516

    55155516
  16. Replies
    56
    Views
    21,633

    Getting back on track

    5507ITs been awhile the winter has takin it toll on any progress . But today I was able to find the best set off exhaust from my parts stash. I so took the motor over to the barn 55085509 time to...
  17. Replies
    56
    Views
    21,633

    the clamps will be unbolted from the plate , then...

    the clamps will be unbolted from the plate , then unbolted from the frame when its on the floor. Still some machining to do on he clamp caps, they 'll need some streamlining for clearance.
  18. Replies
    56
    Views
    21,633

    Very stable, going to shorten the center tube 6",...

    Very stable, going to shorten the center tube 6", its to high as it is. THe gas tank took awhile but zero rust , I put 2 litres of 2 stroke oil in it and roll it around to keep the inside coated.
  19. Replies
    56
    Views
    21,633

    frame

    2707Finally got the stand together and the frame on it. Helps out getting it up off the floor27052706now I can get back to the bike, next will be cleaning up the frame. I painted the frame a...
  20. Replies
    56
    Views
    21,633

    some more work on the stand

    got a couple of hours on my stand, supports welded on with locking studs in place and some paint26352636Kept the feet from on old pool table I scrape. hopefully I'll get the frame on it this weekend....
  21. Replies
    10
    Views
    14,569

    is it toxic or hard to handle and price??

    is it toxic or hard to handle and price??
  22. Replies
    56
    Views
    21,633

    stand

    the sq tubing will have a piece of pipe fit inside it about 3' long which will fit inside another piece of sq tubing at the bottom which is welded to the base on the floor with 4 feet to support the...
  23. Replies
    56
    Views
    21,633

    the reason for the stand is I have very little...

    the reason for the stand is I have very little space in my mini barn, and I"ll need my bike jack for my other bike. This stand will calapsable for storage.
  24. Replies
    56
    Views
    21,633

    clamp base

    back at it today, split and faced blocks .Need to face caps for some clearance. 2472 the clamps fit on the 2 frame rails and a cross bar like in the pic2473 The clamps will be arranged to line up...
  25. Replies
    56
    Views
    21,633

    the frame rails on the bottom are 1" dia , the...

    the frame rails on the bottom are 1" dia , the clamp blocks will be bolted to a base plate that will hold the frame on the frame stand I'm building to hold as I start to reassemble the bike . The...
Results 1 to 25 of 39
Page 1 of 2 1 2