Cafe Racer Forum banner
1 - 4 of 4 Posts

·
Registered
Joined
·
23,303 Posts
I hate to bust your bubble sonny, but megs and pods are not really a heavily modified bike. For all intensive purposes the internals on your bike are stock and will react like a stock bike to changes.

running advanced or retarded timing on a stock bike isn't going to really do anything for you. your stock timing is a balance of low end performance and top end. If you change the timing the bike will run slightly better at one end of the spectrum and really bad at the other.

If you had a radical cam and big bore kit this would be something you would be looking at, but for just pods (which aren't a performance mod BTW) and an exhaust I woudn't bother with it. You won;t get anything out of playing with the timing also because the biggest restriction in a cb750 is the head. Port some of those passages and maybe you can start to see an increase.

In the old days (the 90's...ha) I used to play with the timing on my GTO a lot because I ran a fairly radical cam and high compression and when I couldn't get 94+ octane I would have to retard the timing so the motor wouldn't ping.

You want some cheap performance, 78 cb750 carbs (espically F carbs). Accelerator pump carbs like on the GS and KZ and they are usually worth a good extra kick in the pants, plus smoother throttle response. you will need the rubbers off the same motor but it will make a difference. Also put your stock airbox back on and install a K&N inside.

Edit:
here are hondaman's archived posts on the sohc4 board. READ THESE. And when you are done read them 2 or 3 more times. I am currently looking for his post on cheap tricks on the 750 that is worth reading too.

http://www.sohc4.us/forums/index.php?topic=7401.0

he does describe the differences between the different K model's ignition timing but at one point he does leave out the different cams that honda used. according to honda there is only one cb750 cam but we know this not to be true now and there were several different cam timings (different than ignition timing) for similar grinds.

Also maybe it is time you think about suspension mods too. All that power is no good if you can't find a way to get it to the ground.


Edited by - geeto67 on Aug 21 2007 4:54:05 PM
 

·
Registered
Joined
·
23,303 Posts
If you read hondaman's posts, he does talk about modifying the advance mechanisim for ignition timing to bight it back to K0-K1 specs. However to really reach the performance of k0-k1 you would need to also adjust the cam timing. Either operation is more than I would recommend for a newbie. Also it kills your fuel economy and makes the bike run fineky off of crap gas. Since NY gas is usually pretty rubbish to start there really isn't a benefit.

Koni shocks are kinda expensive. There are other cheaper alternatives. I got redwing shocks brand new oof of ebay for $160 delivered. Vipex perfromance sells a nice remote resovior type shock for the DOHC for $200. That sounds like it won't help until you realize that DOHC 900f stock resovior shocks were considered an upgrade to SOHC suspensions back in the day. be forewarned it will jack the rear of your bike up almost an inch. Hagon shocks are much better than stock too and I have seen them for under $100 a pair.

Those cycle ex 34mm mukunis are a nice setup but for balls to the wall performance I would recommend a set of CR carbs. Cycle-ex also sells them and they are far and away the best performance carb for a SOHC 750 there is. For $100 more than the mukuni kit they are a bargain.

I have DXF file for billet rearsets for a cb750 that a guy on the SOHC board gave to me. I am trying to see if somebody with a CNC machine can use them to mill these. If so - fuck tarrozi's and pony up for these badboys.
 

·
Registered
Joined
·
23,303 Posts
quote:
ohh really? lemme see pls! [email protected]

Banned From The Pubs..
'73 CB350(RIP)
'74 CB750K3 Cafe Thriller

Edited by - wildcatmahone on Aug 22 2007 3:04:34 PM
do you have the ability to read DXF files? Iam trying to find a pick of the bike they guy who gave the the files has. The rearsets looked real nice.


here is a link to vipex performance:
http://www.vipexperformance.com/
the shocks were $242 shipped to my door.


Edited by - geeto67 on Aug 22 2007 4:26:30 PM
 

·
Registered
Joined
·
23,303 Posts
quote:
Geeto, I don't know if it helps but I can access dxf files and convert it to pretty much anything you want. I also have a full size plotter at the office.

****************************************
The best kind of justice is angry mob justice.
Lefty,

I just looked at the original files again and they are .dwg files and not .dxf as I originally thought. the DXFs came from my crudfe conversion program so I could see the files in rhino cad since my older copy did not have the ability to open .dwg files. I think I did not use the the DXF originall because the conversion program skewed the dimensions.

Let me talk to the guy with the CNC and see what file type he needs for the machine to read it and Then I will forward it on to you to convert.

define what you mean by plotter. Like the machine that can spit out a set of paper blueprints? or the one that can take a 3d real life object and convert it to autocad drawings?
 
1 - 4 of 4 Posts
Top